FIAT / DUCATO 244eLearn workshop manual · English · Offline edition
Procedures

3340B52 PUMP/CENTRAL OBS PIPE - R R

Engines: 2.0 16V, 2.0 JTD 8V, 2.3 JTD 16V, 2.8 JTD 8V
Engines: 2.0 16V, 2.0 JTD 8V, 2.3 JTD 16V, 2.8 JTD 8V

RemovingManual illustration 20

RefittingManual illustration 21
- Position the vehicle on the lift.- Remove the protective cap from the bleed valve on the rear brake caliper.- Connect the recovery device (pipe and reservoir) to the rear brake caliper bleed valve.- Operate the brake pedal until the brake/clutch reservoir is drained. Op. 1048A21 FILTER INPUT SLEEVE - R R Op. 1048A10 AIR CLEANER FILTERING ELEMENT - REPLACE Op. 7055B54 UNDER-ENGINE GUARD - R R- Disconnect the negative battery terminal.1. Disconnect the electrical connection for the ABS control unit.
Manual illustration 244000463DescriptionConnector
1ABS control unitM050
2. Undo the connectors for the rigid pipes on the ABS control unit.
Manual illustration 244003923
Engines: 2.0 16V, 2.0 JTD 8V, 2.3 JTD 16V, 2.8 JTD 8V
- Release the two rigid pipes from the master cylinder to the ABS hydraulic control unit from the retaining springs.- Release the two pipes for the additional heater from the spring.- Lower the lift. Op. 1040A30 OIL SEAL COVER, FLY WHEEL SIDE - R + R AND REPLACE SEALS1. Undo the two connectors for the rigid pipes on the brake pump.
Manual illustration 244003924
Engines: 2.0 16V, 2.0 JTD 8V, 2.3 JTD 16V, 2.8 JTD 8V
- Release the two rigid pipes from the retaining springs.1. Remove the rigid pipes from the master cylinder to the ABS hydraulic control unit.
Manual illustration 244003925
Engines: 2.0 16V, 2.0 JTD 8V, 2.3 JTD 16V, 2.8 JTD 8V

RefittingManual illustration 21

RemovingManual illustration 20
- Check that the intermediate flexible pipe to the rear brakes is not damaged.- Fit the rigid pipes from the pump master cylinder to the ABS hydraulic control unit.- Screw in the connectors for the rigid pipes from the master cylinder to the ABS hydraulic control unit without tightening them to torque.- Attach the rigid pipes to the springs.- Attach the pipes for the additional heater to the retaining springs.- Tighten the two connectors for the rigid pipes from the pump master cylinder to the ABS hydraulic control unit.
Manual illustration 244000559Value - daNmFasteningComponentØ  
.(ABS hydraulic control unit ) 1.4ConnectorPIPE FROM PUMP TO HYDRAULIC CONTROL UNITM10
Manual illustration 244000559Value - daNmFasteningComponentØ  
.(ABS hydraulic control unit ) 1.4ConnectorPIPE FROM PUMP TO HYDRAULIC CONTROL UNITM12
- Lower the lift.- Fasten the connectors for the rigid pipes from the master cylinder to the ABS hydraulic control unit to the master cylinder.
Manual illustration 244000559Value - daNmFasteningComponentØ  
.(Master cylinder) 1.4ConnectorPIPE FROM PUMP TO HYDRAULIC CONTROL UNITM10
- Connect the electrical connection for the ABS control unit.
Manual illustration 244000463DescriptionConnector
.ABS control unitM050
- Connect the negative battery terminal. Op. 0010T65 HYDRAULIC BRAKE SYSTEM BLEED AIR- Remove the vehicle from the lift.- Test the operation of the braking system.